Front & Rear Brake Rotors + Ceramic Pads for Chrysler 200 Mitsubishi Lancer

  
Chrysler 200 2011 2012 - 302mm (11.89) Diameter Rear Rotor, Chrysler 200 2013 2014 - 294mm (11.57) Diameter Front Rotor 302mm (11.89) Diameter Rear Rotor, Dodge Avenger 2008 2009 2010 2011 2012 - 302mm (11.89) Diameter Rear Rotor, Dodge Avenger 2013 2014 - 294mm (11.57) Diameter Front Rotor 302mm (11.89) Diameter Rear Rotor, Jeep Compass 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 - 302mm (11.89) Diameter Rear Rotor, Jeep Patriot 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 - 302mm (11.89) Diameter Rear Rotor, Mitsubishi Lancer 2008 - GTS - GTS, Mitsubishi Lancer 2009 - GTS - GTS, Mitsubishi Lancer 2010 2016 - GTS - GTS - GTS Sportback - GTS Sportback, Mitsubishi Lancer 2011 - GTS - GTS - GTS Sportback - GTS Sportback, Mitsubishi Lancer 2017 - GTS - GTS, Mitsubishi Outlander Sport 2011 2012, Mitsubishi Outlander 2008 2009 2010 2011 - 2.4 L4 Engine Exc 3rd Row Seating, Mitsubishi Outlander 2012 2013 - 2.4 L4 Engine FWD, Mitsubishi RVR 2011 2012. 302mm (11.89) Diameter Rear Rotor. 294mm (11.57") Diameter Front Rotor, 302mm (11.89") Diameter Rear Rotor.

2008, 2009, 2010, 2011, 2012. 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017. GTS - GTS - GTS Sportback - GTS Sportback. 2.4 L4 Engine, Exc 3rd Row Seating.

2.4 L4 Engine, FWD. For your new braking system to operate at its performance capacity, it is important to'break-in' the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times.

Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. For Elite XDS & Geomet OE (our coated rotors), and 3 extra minutes.

Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS, not Max Advanced Brakes. Nova Scotia, Prince Edward Island, Newfoundland and Labrador, Alberta, British Columbia. Processing time is subject to change depending on holiday schedule & volume of orders. AB, BC, MB, QC, SK.